Your Plumbing Crash Course: A Guide to Bathtub Installation
Your Plumbing Crash Course: A Guide to Bathtub Installation
Blog Article
What're your beliefs about Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't precisely rocket science, however it does call for solid plumbing, woodworking, and also occasionally, tiling skills. Changing an old bathtub with a new one is additionally a moderately challenging project. If the old tub is easily accessible, the project can relocate quickly; if you have to open up a wall surface to get rid of the old tub as well as position the new bath tub, the job is much harder. In either instance, the job is within a house handyman's abilities, although you will require a helper to vacate the old tub and embeded in the brand-new one. Make sure you have actually certified on your own for the job and are comfortable attempting it. Instead of hiring a service provider to take control of a halfway-completed job, it is much better to consider using one before you start. Possibilities are you may need a specialist plumber to make tube links.
This post will certainly help you install a new tub in your bathroom if you have already acquired a brand-new tub as well as do not require to transform the plan of your previous water system pipes.
Your devices and material list ought to make up the following:
Preparing for the Installation
First of all, the sustaining structure provided with the bath should be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to prevent stress on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final placement.
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be fairly bothersome due to the limited gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the continuing to be water that will originate from the pipelines. Once the supply pipes have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Before going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, put the bathtub in the called for placement. The wood boards are practical in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four small points.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the bath tub till the level reviews level.
To mount taps, fit all-time low of the furthest versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the supply of water and examine all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill up the bath tub as well as also check the overflow electrical outlet and also the typical outlet for leaks.
Ultimately, take care of the bath paneling as explained in the maker's user's manual. Tiling and also securing around the tub must wait till the tub has actually been made use of at the very least when as this will resolve it right into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making certain that the washers are in area between the faucet and the sink. Safeguard the faucet in place with the supplier supplied backnut. As soon as the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet connectors. The former type should be connected to the faucet finishes initially, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a rigid seal, triggering the water to penetrate the wall surface in between the bathroom and also the tiling, leading to issues with moisture and feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to permit the motion experienced when the tub remains in usage. The sealer can fracture fairly very early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the market. It is recommended to fit the floor tiles using waterproof or water-proof sticky as well as grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Hopefully you liked our section about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for spending some time to browse our post. Appreciated our blog entry? Please share it. Help someone else discover it. We love reading our article about A Step-by-Step Guide to Installing a Bathtub.
Damage control? Call us. Report this page